How To Vacuum Intex Pool With Sand Filter?

Intex pools are a great option for people looking for an affordable and easy-to-install pool. The pools come with a sand filter, which needs to be cleaned every few weeks to keep the pool functioning properly. This article will teach you how to vacuum intex pool with sand filter.

Sand filters remove contaminants in the pool water and clean the water for use in the pool.

A vacuum is required to take out dirt, debris, and bugs that get into your Intex pool when it is not in use. Without a vacuum, leaving the filter running 24/7 will produce very poor results and can cause damage to your sand filter.

Tips:

  1. Unscrew the filter system on top of your Intex pool and remove the debris bag. Remove all water from the filter canister by gently pressing on it to get any remaining liquid out. Use a clean cloth towel to get rid of more liquid, if needed.
  2. Attach hose #3 (the hose with the widest opening) to the closest fitting on your Intex valve.
  3. Attach hose #2 (the longer one with holes and a handle at the end) to hose #3.
  4. Put hose #2 into clean water and use it to flush out any dirt or debris in the filter canister.
  5. Attach the vacuum head to hose #2.
  6. Turn on your Intex pump and put it into filter mode. You can find the mode by looking on the side of your Intex pump for words such as “filter,” “vacuum,” or “clean.” Set this mode to high so that the waste will be sucked up from the bottom of the pool.
  7. Move the vacuum head up and down throughout the pool to clean it thoroughly. Because your filter is still running, you should see dirt or debris being sucked into the waste bag attached to the vacuum head.
  8. Turn off both your Intex pump and filter system when you are finished vacuuming.

How To Vacuum Intex Pool With Sand Filter

What Do You Need to Know Before Vacuuming Your Pool?

Before vacuuming your pool, you should make sure that the pump is turned off and the filter is disconnected from the pump.

If the filter is not disconnected, it will suck air and create a vacuum, which will damage the pump.

You should also remove any toys or debris from the pool before vacuuming. This will help ensure that the vacuum cleaner picks up as much dirt and debris as possible.

How Does a Sand Filter Work?

A sand filter works by using a layer of sand to trap dirt and debris. The dirt and debris are then removed from the pool by cleaning the filter. This allows the pool to run cleaner for a longer period of time.

How Do You Know When It’s Time To Vacuum The Intex Sand Filter?

There are several indicators that will let you know when it is time to clean your sand filter. If the water turns cloudy after you clean it, then there is debris in the filter which you need to clean.

You can also tell that it is time to vacuum the filter when you notice that your water isn’t as clear as before, or if the chemical balance of your pool gets out of whack.

How Do You Clean The Intex Sand Filter?

There are several ways you can clean a sand filter. One way is to backwash the filter. This is done by first turning off all of the filter’s valves, and then making sure that the pump is turned on.

Next, you will need to disconnect the hoses from both ends of your filter. You can now remove any debris trapped in it by hand or with a skimmer.

Once you’ve removed as much as you can, you should turn your filter back on and allow the water to flow through it. This should clear out anything left over from the debris which you removed.

Afterward, reconnect the hoses to both ends of your sand filter and check the pressure gauge to make sure that it is between 90 psi-145 psi. If it’s not within that range then your filter may need to be replaced.

Vacuum Process with Sand Filter

The first step in vacuuming an Intex pool with a sand filter is to remove the top cap from the filter.

Once the cap is off, you will see the inside of the filter. There is a black ring around the edge of the filter. This ring needs to be cleaned before you can vacuum the pool.

To clean the ring, use a brush or a scouring pad to scrub it until it is clean. Once the ring is clean, you can put the top cap back on the filter.

Next, you need to remove the plug from the bottom of the filter. This will allow water to flow from the pool into the filter.

Once the plug is removed, you can turn on the pump and insert the water vacuum into the pool.

Then, dive down and attach the vacuum to the bottom of the pool.

The next step is to turn on the pump again and wait for it to draw water from the pool up through the filter and back into the pool. When this happens, you will see dirty water coming out of the pool’s return line.

Once the pool looks clean, you need to take the vacuum off of the bottom of the pool. Then, shut off the pump and remove it from the pool.

The final step is to put back in the plug that allows water to flow into your Intex filter. Next, you can put back on that top filter cap and complete your maintenance by filling up the pool.

Final Thoughts:

If you follow these steps, you should be able to use an Intex sand filter just like any other pool. All it takes is a little bit of elbow grease and you’ll have the cleanest pool around.

Scroll to Top